Programing The Realistic Pro 91 And Pro 94 Trunk Tracker Scanners.
                     For The Knoxville Tennessee Area
*****************************************************************************
                             By Eddie Conner


Turn the scanner on, Press the "Truck" Button. The numbers will be flashing 
on top of display for the banks you want to enter your Fleet Map into. Then 
press the bank number you want to program Your Fleet Map in. Preferably 
Bank 1. Your Scanner will stop on Bank 1. (*THIS NEXT STEP CRITICAL*). You 
must enter the Fleet Map EXACTLY as it is shown below in the "Trunk Mode". 
In some of the Radio Shack Owners Manual's this is listed incorrectly. The 
list listed below is For Knox County Emergency Communication District. It is 
as follows. (*IMPORTANT*, *These Frequencies Must Be Entered Exactly In 
Order Shown Below.*)From left to right Starting with Channel 1 & Ending 
with channel 19.*

                          *Knox County Fleet Map*
-----------------------------------------------------------------------------
Ch-1= 856.2125 Ch-2= 856.4375 Ch-3= 856.7125  Ch-4= 856.9375  Ch-5= 867.2125 
Ch-6= 857.4375 Ch-7= 857.7152 Ch-8= 857.9375  Ch-9= 858.2125  Ch-10=858.4375
Ch-11=858.7125 Ch-12=858.9375 Ch-13=859.9125  Ch-14=859.4375  Ch-15=859.7125
Ch-16=859.9375 Ch-17=860.2125 Ch-18=860.4375  Ch-19=860.7125  Ch-19=860.9375
-----------------------------------------------------------------------------
              Ok now you should have the Fleet Map programed. 

                     Now programing the Sub Fleet Map.
---------------------------------------------------------------------------

1. Set the scanner for conventional scanning. Press the "PROG" button then 
press the "TRUNK" Button.

2. Press the number key of the bank where you want to store the sub fleet 
map. (This Should Be bank 1).

3. Repeatedly Press Up or down Arrows located on the bottom left face until
"E1" appears, then press "E". A trucked frequency you previously programmed 
appears.

4. Press "DATA" . A preprogrammed fleet map appears.

5. Repeatedly press the Up and Down arrows on the bottom left until "USr" 
appears. Then Press "E".

6. Press "DATA"

7. Repeateatedly press the "UP" and "DOWN" arrows to select the size code 
for the first block, then press "E". The next available block appears.
(SEE BELOW)

8. Repeat Step 7 until you have selected a size code for for each desired 
block.(SEE BELOW)

9. Press "SRC" (LIMIT). The scanner exits the trunking programming mode, 
tunes the data channel, then searches using the map you programed.

-----------------------------------------------------------------------------
           The Block Code For Knox County Fleet Map Is As Follows.

      
Block 0 = S0 / Block 1 = S0 / Block 2 = S12 / Block 3 DN/A Block 4 = S12 / 
Block 5 DN/A / Block 6 = S3 / Block 7 = S11
----------------------------------------------------------------------------

   If all entered correctly your scanner should now be scanning the 800MHZ 
                               Trunking Band.


        Refer to below address for Knoxville And Knox County Fleet Maps. 

                 http://www.alltel.net/~weconner/trunkinfo.html



-----------------------------------------------------------------------------
                                 *(Disclaimer)*

            Programimg these scanners should cause no harm. However
             I accept no responsibility for any damage which might 
            occur while programing these scanners. By attempting do 
            to so you release me from ANY and ALL future liability.
          In some states having a scanner in your vehicle is illegal.
    Please check your local scanner laws. Scanning for illegal purposes is 
    strictly prohibited by law and can carry a hefty fine plus Imprisonment.

-----------------------------------------------------------------------------
 It is strongly recommended that if you are new to Trunking, goto any search 
  engine and search for Trunking Radio. This will explain all aspects of 
                                   Trunking.

                                  *Good Luck*
-----------------------------------------------------------------------------
                                     Terms

                             DN/A = Does Not Apply
                             PROG = Program Button
-----------------------------------------------------------------------------


                                weconner@bellsouth.net

                          http://personal.lig.bellsouth.net/lig/w/e/weconner/